Search results for "molybdenum oxide"
showing 10 items of 14 documents
"Partial oxidation of methane and methanol on FeOx-, MoOx- and FeMoOx -SiO2 catalysts prepared by sol-gel method: a comparative study"
2020
[EN] FeOx-, MoOx and FeMoOx-SiO2 materials prepared by a sol-gel procedure have been evaluated as catalysts for the partial oxidation of methane and methanol. The effect of decreasing the pH of the synthesis gel on the chemical nature of FeOx and MoOx species has been investigated. Characterization results show that low pH improves the dispersion of metal oxide species present in SiO2 matrix. For FeOx/SiO2 materials, the presence of dispersed FeOx species (rather than bulk Fe2O3) improves the selectivity to formaldehyde in the partial oxidation of methane and methanol. For FeMoOx/SiOx catalysts, dispersed species favor the selectivity to formaldehyde only for methane oxidation. In contrast,…
Efficient Vacuum Deposited P-I-N Perovskite Solar Cells by Front Contact Optimization.
2020
Hole transport layers HTLs are of fundamental importance in perovskite solar cells PSCs , as they must ensure an efficient and selective hole extraction, and ohmic charge transfer to the corresponding electrodes. In p i n solar cells, the ITO HTL is usually not ohmic, and an additional interlayer such as MoO3 is usually placed in between the two materials by vacuum sublimation. In this work, we evaluated the properties of the MoO3 TaTm TaTm is the HTL N4,N4,N4 amp; 8243;,N4 amp; 8243; tetra [1,1 amp; 8242; biphenyl] 4 yl [1,1 amp; 8242; 4 amp; 8242;,1 amp; 8243; terphenyl] 4,4 amp; 8243; diamine hole extraction interface by selectively annealing either MoO3 prior to the deposition of TaTm o…
Erratum to: Sub-gap defect density characterization of molybdenum oxide: An annealing study for solar cell applications
2022
Characterization of the defect density states in MoOx for c-Si solar cell applications
2021
Thin layers of MoOx have been deposited by thermal evaporation followed by post-deposition annealing. The density of states distributions of the MoOx films were extracted deconvoluting the absorption spectra, measured by a photothermal deflection spectroscopy setup, including the small polaron contribution. Results revealed a sub-band defect distribution centered 1.1 eV below the conduction band; the amplitude of this distribution was found to increase with post-deposition annealing temperature and film thickness.
Sub-gap defect density characterization of molybdenum oxide: An annealing study for solar cell applications
2020
AbstractThe application of molybdenum oxide in the photovoltaic field is gaining traction as this material can be deployed in doping-free heterojunction solar cells in the role of hole selective contact. For modeling-based optimization of such contact, knowledge of the molybdenum oxide defect density of states (DOS) is crucial. In this paper, we report a method to extract the defect density through nondestructive optical measures, including the contribution given by small polaron optical transitions. The presence of defects related to oxygen-vacancy and of polaron is supported by the results of our opto-electrical characterizations along with the evaluation of previous observations. As part…
Use of Hydrogen Molybdenum Bronze in Vacuum‐Deposited Perovskite Solar Cells
2019
Herein, the dehydration of a hydrogen molybdenum bronze (HYMoO3), converting it to molybdenum oxide (MoOX), is explored toward the development of perovskite solar cells (PSCs) for the first time. H0.11MoO3 bronze is synthesized, characterized, and deposited on indium tin oxide (ITO) under different concentrations and annealing conditions for in situ conversion into MoOX with appropriate oxygen vacancies. Vacuum‐deposited PSCs are fabricated using the as‐produced MoOX hole injection layers, achieving a power conversion efficiency of 17.3% (average) for the optimal device. The latter has its stability and reproducibility tested, proving the robustness and affordability of the developed hole t…
Design of Molecular Spintronics Devices Containing Molybdenum Oxide as Hole Injection Layer
2017
Nonprecious Copper‐Based Transparent Top Electrode via Seed Layer–Assisted Thermal Evaporation for High‐Performance Semitransparent n‐i‐p Perovskite …
2019
Semitransparent perovskite solar cells (ST‐PSCs) are highly attractive for applications in building‐integrated photovoltaics as well as in multijunction tandem devices. To fabricate high‐performance ST‐PSCs, suitable transparent top electrodes are strongly needed. Dielectric/metal/dielectric (DMD) multilayer structures have been shown to be promising candidates, though generally based on high‐value metals such as gold or silver, the latter causing also stability issues by reacting with perovskite. Here, a novel DMD transparent electrode based on nonprecious, less‐reactive copper is developed via thermal evaporation and used as a top anode in the fabrication of high‐performance semitranspare…
Electrodeposition from molybdate aqueous solutions: a preliminary study
2013
The electrochemistry of molybdenum (Mo) and its oxides is very important for several applications in electrocatalysis,batteries,sensors and in particular for CIGS-based solar cells,where metal Mo is used as back contact.Properties and the fabrication method of Mo films are of fundamental importance,because they could induce significant changes in solar cell performances.The most important issues in the electrochemical behaviour of Mo are the nature and stability of its surface oxides,which are strongly dependent on deposition bath pH.Ivanova et al. (2006) reported that it is possible to accomplish the cathodic reduction of molybdate ions to metallic Mo from electrolytes containing HF.The ad…
Characterization of defect density states in MoOx for c-Si solar cell applications
Layers of MoOx have been deposited by thermal evaporation followed by post-deposition annealing (PDA). The density of states (DOS) distributions of the MoOx films were extracted deconvoluting the absorption spectra, measured by a phothermal deflection spectroscopy setup, including the small polaron contribution. Results revealed a sub-band defect distribution centered 1.1 eV below the conduction band; the amplitude of this distribution was found to increase with PDA temperature and film thickness.